Home » » Cara Membuat Filter Air Sederhana

Cara Membuat Filter Air Sederhana

The drawing at the top of this page is a quarantine tank I put together for Dale and Patti Gingerich. It can be run with just the barrel filter when the ball valve is fully open or it can be run completely through the 4 barrel tower with the ball valve closed or a combination of both by partially closing the ball valve. This filtration system would handle a 1000 gallon pond without a hiccup.
Gambar 1:
Four Barrel Trickle Tower and Drum Filter

Gambar 2:
This picture shows the bottom of the 300 gallon Rubber Maid stock tank with the drains installed.


Gambar 3:
This is the way I build the 4 barrel tower.
Use a 1-1/2" PVC cross. You can get them in white schedule 40 PVC at Lowe's, Home Depot or other plumbing sources. Use a hole saw and cut a hole in the center to accept a 1-1/2" PVC pipe.

Gambar 4:

Use four pieces of 4" ABS pipe. The length can be adjusted to your needs for the space you have available. The ones I did for Dale and Patti are 48" long. The holes need to be approximately 2-1/4" in diameter but I used a smaller hole saw and enlarged them with a drimmel sanding disc in my drill.

Gambar 5:

You want outlets of the PVC cross to fit tightly in the holes. I beveled the ends of the outlets to get them started in the holes and forced them the rest of the way.

Gambar 6:

Once I assembled the PVC cross and the four sections of ABS pipe I glued a short piece of 3" ABS pipe in the center (not shown) to make them stable. Always use "All Purpose" glue when gluing ABS

Gambar 7:

Drill 3/8 or 1/2" holes in the end of four 4" ABS end caps and glue them to the bottom ends of the pipes. Fill the pipes with bio balls or another plastic media that has a good flow through. I don't recommend Kaldness. It would trap too much of the bacteria that dies and sluffs off.

Gambar 8:


This shows the inside of the 55 gallon drum with the 2" shower drain for the bottom drain. The reason it is positioned where it is, is because it is one of the lowest points in the barrel and it was the only smooth place on the bottom. Ideally it would be in the exact center but there is a mold seam there and it will not allow a good seal.

Gambar 9:

Here it is with the inlet. The 2" bulkhead fitting is the same as the one at the top left but it isn't visible in the picture due to the shadow. By installing the inlet like this it will slow the water down some and help with settlement. It also will be a support for the 24" "Matala Round" media I'll use first.

Gambar 10:

By installing the outlet like so the PVC pipe will serve to hold the media down and with the elbow turned up it will pick up oxygen before going back to the pond. When using it before a pump as in Dale and Patti's application you need to turn the elbow down and use a pipe strainer on the end.

Gambar 11:

This filter can be pump fed or gravity fed. With the 2" inlet and outlet a flow rate of 600-1,000 gph is recommended. If you gravity feed the filter with the pump after you will need to turn the elbow down so it doesn't pick up any air. The poly drums I use most have an inside diameter of 24" and the 24" Matala Rounds fit very nicely. I am using the green for the first stage of media.

Gambar 12:
The bird netting is folded 3 ways so I unroll it, spread it out, gather it up and stuff it into the barrel.
I use a piece of egg crate to help hold the netting below the water with the outlet pipe over that. If you build one of these filters make sure any of the media you use can't get drawn into the outlet and clog it. If you have it outside cover the top of the barrel so leaves or other debris can't get in and stop up the outlet. Be sure to leave an air space between the lid and the barrel. I use heavy shade cloth to cover mine outside.

Gambar 13:
A picture of the bottom drain.

Gambar 14:
I set the new barrel filter up on a reservoir tank.





sumber: http://www.koiclay.com/diy/pg5.htm
Share this post :
 
Support : JUAL | IKAN | SIDAT
Copyright © 2012. Sidat Masapi - All Rights Reserved